To season a carbon steel pan, wash it in hot water, dry it thoroughly, then heat it with a very thin film of oil until the oil starts to smoke lightly. Wipe it, let it cool and repeat: at least three coats are recommended. Each coat turns the oil into a hard, dark brown to black layer that protects the steel from rust and gradually stops food from sticking.
Steel pan, carbon steel pan, iron pan or sheet steel pan: these names all refer to the same type of bare metal pan, with no synthetic non-stick coating. This guide explains the step-by-step method, which oil to choose, the mistakes to avoid and everyday care.
Why season a carbon steel pan?
A new carbon steel pan is bare metal. It comes protected by a factory wax or oil, which is not meant for cooking and must be removed with the first wash. Without seasoning, the steel oxidises easily when exposed to moisture and food sticks.
Seasoning creates a thin protective layer directly on the steel. Unlike an industrial coating, this layer gets stronger every time you cook with a little fat: the darker the pan gets, the less food sticks. A seasoned pan therefore improves with use instead of wearing out.
Which oil should you use to season a carbon steel pan?
You need a neutral, refined vegetable oil that withstands heat well. An oil that burns at a low temperature may burn off before it hardens and leave an uneven seasoning.
| Oil or fat | Suitable for seasoning? | Good to know |
|---|---|---|
| Grapeseed | Yes | Often recommended by carbon steel pan makers. |
| Rapeseed (canola) | Yes | Common and inexpensive. |
| Sunflower | Yes | Widely used for this purpose. |
| Peanut | Yes | Also suitable; if someone at home has a peanut allergy, choose another oil. |
| Linseed (flaxseed) | Opinions differ | Some cooks recommend it, others advise against it; for a first seasoning, a neutral oil is simpler. |
| Virgin olive oil | No | It burns quickly and at a low temperature. |
| Butter, solid fats | No | They burn too quickly to give an even seasoning. |
How to season a carbon steel pan, step by step
The thin-film method, where the oil is wiped off and then heated, is the simplest in a home kitchen, especially on a gas hob. Here are the steps.
- Wash the new pan in very hot water with a sponge, scrubbing well to remove the manufacturer's protective wax or oil;
- Dry it carefully, leaving not a single drop of water, as moisture prevents the oil from bonding;
- Oil: put a few drops of oil (a teaspoon or less) on a paper towel, rub the whole inside surface, then wipe with a clean paper towel until the pan looks almost dry. If you can see the oil, there is still too much;
- Heat over medium to high heat, with a window open or the extractor hood on, until light smoke appears and the bottom changes colour. Allow about 5 minutes;
- Wipe: turn off the heat, let the pan cool for a few minutes, then remove any excess oil with a paper towel (use tongs if the pan is still hot);
- Repeat steps 3 to 5 at least twice more, for a minimum of three coats. The pan gradually turns from grey to golden, then brown and black.
Heavy smoke is normal during the first few minutes. However, a flame or black, acrid smoke means the heat is too high: turn it down.
Which seasoning method should you choose?
| Method | How it works | When to choose it |
|---|---|---|
| Thin film of oil, wiped off | A few drops of oil spread with a paper towel, heated until lightly smoking, wiped, then repeated. | The simplest for everyday use, on gas or on an electric hob. |
| Oil heated then poured off | About 1 mm of oil in the bottom, heated until lightly smoking, carefully poured into a container, then wiped. | The method given in several manufacturers' instructions; it calls for care, as the oil is very hot. |
| In the oven or on the barbecue | The whole pan oiled and heated for longer. | On a ceramic hob, to oil the underside as well; avoid with a wooden or plastic handle. |
Seasoning a carbon steel pan on an induction hob
Induction heats very strongly and very quickly, and steel conducts heat very well. Manufacturers therefore advise:
- using a moderate temperature;
- not using the "booster" function;
- not leaving the empty pan to heat for too long, especially from 26 cm in diameter.
Common problems after seasoning
| Problem | Likely cause | Solution |
|---|---|---|
| Sticky or tacky surface | Too much oil, or not enough heat for the oil to harden. | Heat the pan until the residue softens, scrub it with hot water and coarse salt, dry, then start again with a much thinner film of oil. |
| White spots after cooking | Acidic food (tomato, white wine, lemon) that damages the seasoning. | Season the pan again. |
| Rust spots | Pan stored damp or not dried properly. | Remove the rust with a stiff brush, then season again. |
| Patchy bottom, some areas darker than others | Uneven spread of oil or uneven cooking. | Harmless if the surface is not sticky: the colour evens out with use. |
Caring for a seasoned carbon steel pan
- Let the pan cool slightly before putting it under water, to avoid thermal shock;
- Clean it with hot water and a sponge, without detergent and never in the dishwasher, as both damage the seasoning;
- Avoid steel wool, which strips the protective layer, except to redo a failed seasoning;
- For stubborn residue, scrub with coarse salt and a little hot water;
- Dry immediately, then wipe on a very thin layer of oil with a paper towel;
- Store the pan in a dry place.
FAQ
Do you need to season a carbon steel pan before using it for the first time?
Yes. A carbon steel pan is delivered as bare metal, with only a factory protective coating. Seasoning it before the first use reduces the risk of food sticking and protects the steel from rust.
How many times should you season a carbon steel pan?
At least three coats are recommended for a first seasoning. Some cooks do more, up to around ten, to get a tougher surface from the start. Either way, the seasoning keeps building up every time you cook with fat.
What is the best oil for seasoning a carbon steel pan?
A neutral, refined vegetable oil: grapeseed, rapeseed, sunflower or peanut oil all work. Virgin olive oil, butter and solid fats should be avoided, as they burn too quickly.
Is it normal for the pan to smoke a lot during seasoning?
Yes, smoke is normal: it shows that the oil is hardening onto the steel. It dies down after a few minutes. Ventilate the room, and lower the heat if the smoke turns black and acrid.
Why is my carbon steel pan sticky after seasoning?
Almost always because there was too much oil, or the heat was not high enough. Heat the pan to soften the residue, scrub it with hot water and coarse salt, dry, then start again with a much thinner film of oil.
Can you wash a seasoned carbon steel pan with washing-up liquid?
It is best avoided. Hot water and a sponge are enough for everyday use. The dishwasher and detergents are not recommended, as they damage the seasoning.
Can a carbon steel pan rust despite the seasoning?
Yes, if it is stored damp or the seasoning is insufficient. This is not permanent: remove the rust with a stiff brush, then season the pan again.
Can you cook acidic food in a seasoned carbon steel pan?
Yes, but acidic food can damage the seasoning and leave white spots, especially while the pan is not yet well blackened. In that case, simply season the pan again.
Find out more
Browse our selection on La Fabriculture's frying pan page, and find our advice on caring for steel and stainless steel in our care guide.



